Sleeping aid based on electromagnetic field radiation

Posted by Author makecircuits

Sleeping aid based on electromagnetic-field radiation

Based on electromagnetic-field radiation

Place it under the pillow - Built-in timer

Parts:

R1,R5___________1K 1/4W Resistors R2_____________10K 1/4W Resistor R3,R6__________10M 1/4W Resistors R4,R7___________2M2 1/4W Resistors R8,R9___________4K7 1/4W Resistors C1,C7__________47΅F 25V Electrolytic Capacitors C2____________100nF 63V Polyester Capacitor C3,C4_________330nF 63V Polyester Capacitors C5,C6__________15nF 63V Polyester Capacitors D1,D3,D4,D5__1N4148 75V 150mA Diodes D2______________LED (any type) (see Notes) IC1____________4060 14 stage ripple counter and oscillator IC IC2____________4093 Quad 2 input Schmitt NAND Gate IC Q1____________BC327 45V 800mA PNP Transistor L1____________Radiator coil (see Notes) P1____________SPST Pushbutton SW1___________2 poles 4 ways rotary switch SW2___________SPST Slider Switch B1____________9V PP3 Battery

Features:

Generates a natural electromagnetic-field

Makes easier to fall asleep

Induces a prolonged and sound sleep without drugs

No side effects

Device purpose:

Many people experienced sleeping well in natural surroundings, into a tent or a wooden hut. This fact is due not only to the healthy atmosphere but also from our unconscious ability to perceive natural Earth`s magnetic-fields.

The circuit generates this type of Geo-magnetic-fields and lets us perceive them: in this manner our brain is surrounded by an ideal environment for a sound sleep. (N.B. Basic ideas for this circuit are coming from German papers).

Use:

  • Select a timing option by means of the rotary switch SW1.

  • Choose 15, 30 or 60 minutes operation.

  • Select "Stop" or "Alternate" mode operation by means of SW2.

  • With SW2 closed (Stop mode operation) the electromagnetic radiation stops after the pre-set time is elapsed.

  • With SW2 opened (Alternate mode operation) the device operates for the pre-set time, then pauses for the same amount of time: this cycle repeats indefinitely.

  • Place the unit under the pillow and sleep like a log.

  • To reset a cycle press P1 pushbutton.

Circuit operation:

IC2C and IC2D generate tw1o square waves at about 1.2 and 5 Hz respectively. These wave-forms are converted into 60΅S pulses at the same frequencies by means of C5 & C6 and mixed at Q1`s Base. This transistor drives the Radiator coil with a scalar series of pulses of 60΅S length and 9V amplitude.

IC1, IC2A & IC2B form the timer section. C1 & R2 provide auto-reset of IC1 at switch-on. The internal oscillator of IC1 drives the 14 stage ripple counter and, after about 15 minutes, output pin 1 goes high. Pin 3 of IC2A goes low and stops IC2C & IC2D oscillation.

If SW2 is left open (Alternate mode operation), after 15 minutes pin 1 of IC1 goes low, pin 3 of IC2A goes high and oscillators are enabled again.

If SW2 is closed (Stop mode operation), the first time output pin 1 of IC1 goes high, the internal oscillator of the IC is disabled by means of D1. Therefore the circuit remains off until a reset pulse is applied to pin 12 by means of P1 or when the whole device is switched-off and then restarted.

The same thing occurs when SW1 is switched on 30 or 60 minutes positions, obviously changing time length.

IC2B drives pilot LED D2 which operates in the following three modes:

  • flashes quickly and almost randomly when the Radiator coil is driven

  • flashes somewhat slowly and regularly when the Radiator coil is pausing during the Alternate mode operation

  • is off when the circuit auto-stops (Stop mode operation)

Notes:

  • L1 is obtained by winding randomly 600 turns of 0.2 mm. enameled wire on a 6 mm. diameter, 40 mm. long, steel bolt. Secure the winding with insulating tape.

  • Mean current drawing is about 7mA, decreasing to less than 4mA during pauses when in Alternate mode operation.

  • Battery life can be dramatically increased omitting LED D2 and its associated resistor R5.

  • Use a plastic box to enclose the circuit: metal cases can severely limit electromagnetic radiation.